Tungsten Lamps as an Affordable Light Source for Testing of Photovoltaic Cells

An improved Tungsten light source system for photovoltaic cell testing made from low-cost, commercially available materials is presented as an alternative to standard expensive testing equipment. In this work, spectral correction of the Tungsten light source is achieved by increasing the color temperature to ??5200 K using inexpensive commercially available filters. Spectral measurements of the enhanced light source reveal that a better spectrum match towards the solar spectrum is achieved than what has been previously demonstrated. Specifically, the improved solar spectrum match is achieved by substantial filtering of the infrared range. The proposed setup is used to evaluate the performance of both silicon and organic based photovoltaic cells.     

The effect of nano-size additives on the electrical conductivity of matrix suspension and properties of self-flowing low-cement high alumina refractory castables

Influence of two nano-size additives on electrical properties of suspension matrix of self-flowing low-cement high alumina refractory castable is investigated. For this purpose, castament FS 10 and FS 20 on the basis of polycarboxylate ether were considered. The self-flow value, workability and mechanical strength of the castable are evaluated and their relations with electrical conductivity are determined. Using these relations, the type and optimum amount of proper additive for these refractory castables are determined. It was shown that if the electrical conductivity of matrix suspension is less than 0.71 mS/cm, high alumina low-cement self-flowing refractory castable can be obtained. The best self-flow, sufficient working time and adequate mechanical strength in the castables are obtained with 0.08 wt.% FS 20.     

Polystyrene/Polyolefin Elastomer Blends Loaded with Halloysite Nanotubes: Morphological,Mechanical, and Gas Barrier Properties

Herein, a simple melt-blending method is utilized to disperse of halloysite nanotubes (HNTs) in polystyrene/polyolefin elastomer (PS/POE) blends. Based on morphological studies, the PS/POE/HNT nanocomposite containing up to 3 phr HNTs shows excellent nanofiller dispersion, while those filled with 5 phr HNTs exhibit nanofiller aggregation. To overcome the nanofiller aggregation issue, the polypropylene-grafted-maleic anhydride (PP-g-MA) compatibilizer is added to the PS/POE/HNT nanocomposite, which results in improved mechanical properties for the nanocomposite sheets. Furthermore, the addition of compatibilized HNTs to the PS/POE blends leads to decreased O₂ and N₂ gas permeabilities. Besides, incorporating POE, HNTs, and PP-g-MA leads to a decrease in water vapor transmission of PS. In the end, the experimentally-determined mechanical properties and gas permeabilities of the nanocomposite sheets are compared to those predicted by prevalent theoretical models, revealing a good agreement between the experimental and theoretical results. Molecular-dynamics simulations are also carried out to calculate the gas diffusion coefficients in the different sheets to further support the experimental findings in this study. Overall, the PS/POE/HNT/PP-g-MA nanocomposite sheets fabricated in this work demonstrate excellent mechanical and gas barrier properties; and hence, can be used as candidate packaging materials. However, the strength of the resulting PS/POE blend may be inferior to that of the virgin PS.     

A clustering-based modified variable neighborhood search algorithm for a dynamic job shop scheduling problem

The dynamic job shop scheduling (DJSS) problem occurs when some real-time events are taken into account in the ordinary job shop scheduling problem. Most researches about the DJSS problem have focused on methods in which the problem’s input data structure and their probable relationship are not considered in the optimization process while some useful information can be extracted from such data. In this paper, the variable neighborhood search (VNS) combined with the k-means algorithm as a modified VNS (MVNS) algorithm is proposed to address the DJSS problem. The k-means algorithm as a cluster analysis algorithm is used to place similar jobs according to their processing time into the same clusters. Jobs from different clusters are considered to have greater probability to be selected when an adjacent for a solution is made in an optimization process using the MVNS algorithm. To deal with the dynamic nature of the problem, an event-driven policy is also selected. Computational results obtained using the proposed method in comparison with VNS and other common algorithms illustrate better performance in a variety of shop floor conditions.     

Molecular dynamics simulations of vinyl ester resin monomer interactions with a pristine vapor-grown carbon nanofiber and their implications for composite interphase formation

A molecular dynamics simulation study was performed to investigate the role of liquid vinyl ester (VE) resin monomer interactions with the surface of pristine vapor-grown carbon nanofibers (VGCNFs). These interactions may influence the formation of an interphase region during resin curing. A liquid resin having a mole ratio of styrene to bisphenol-A-diglycidyl dimethacrylate VE monomers consistent with a commercially available 33 wt.% styrene VE resin was placed in contact with both sides of two pristine graphene sheets overlapped like shingles to represent the outer surface of a pristine VGCNF. The relative monomer concentrations were calculated in a direction away from the graphene sheets. At equilibrium, the styrene/VE monomer ratio was higher in a 5 Å thick region adjacent to the nanofiber surface than in the remaining liquid volume. The elevated concentration of styrene near the nanofiber surface suggests that a styrene-rich interphase region, with a lower crosslink density than the bulk matrix, could be formed upon curing. Furthermore, styrene accumulation in the immediate vicinity of the nanofiber surface might, after curing, improve the nanofiber–matrix interfacial adhesion compared to the case where the monomers were uniformly distributed throughout the matrix.     

A Comprehensive Experimental Study on Finishing Aluminum Tube by Proposed UAMAF Process

In this paper, a new noncontact ultrasonic magnetic abrasive finishing mechanism is presented. An ultrasonic vibration producer is used to vibrate the permanent magnets. The ferromagnetic steel grits in the created magnetic field form a flexible finishing tool. To take advantage of cavitation collapse pressure, the finishing zone components are immersed in water. The present work also studies the effect of parameters, i.e., time duration for finishing and working gap between magnetic poles and the workpiece on the surface roughness (Ra). The microscopic pictures and the roughness profile diagrams demonstrate the advantages of the proposed method.     

Anisotropic diffusion for noise removal of band pass signals

A noise removal method for band pass signals based on the anisotropic diffusion algorithm originally put forward by Perona and Malik is proposed in this paper. The anisotropic smoothing algorithm proposed here is for band pass signals modulated with a constant carrier frequency. A partial differential equation to smooth band pass noisy signals is derived. The propagator of this differential equation is also analytically calculated in this paper. An appropriate linear operator is then considered here for such band pass signals to form an anisotropic diffusion algorithm. The algorithm proposed here demonstrates better performance for band pass noisy signals containing discontinuities in comparison with the traditional Perona-Malik (PM) algorithm and is robust in the presence of excessive noise with SNR less than unity.     

Reactive capability limitation of synchronous machines

Achievable generator reactive capability (GRC) is generally much less than indicated by manufacturers' reactive capability curves, due to constraints imposed by plant auxiliaries and the power system itself. The nature of these constraints is explained and a method for calculating them is provided and verified by field tests on a unit at high and low power system voltage levels. Several recommendations are made to enhance the GRC of the tested unit     

Blue Light Improves Photosynthetic Performance during Healing and Acclimatization of Grafted Watermelon Seedlings

To investigate the importance of light on healing and acclimatization, in the present study, grafted watermelon seedlings were exposed to darkness (D) or light, provided by blue (B), red (R), a mixture of R (68%) and B (RB), or white (W; 35% B, 49% intermediate spectra, 16% R) LEDs for 12 days. Survival ratio, root and shoot growth, soluble carbohydrate content, photosynthetic pigments content, and photosynthetic performance were evaluated. Seedling survival was not only strongly limited in D but the survived seedlings had an inferior shoot and root development, reduced chlorophyll content, and attenuated photosynthetic efficiency. RB-exposed seedlings had a less-developed root system. R-exposed seedlings showed leaf epinasty, and had the smallest leaf area, reduced chlorophyll content, and suppressed photosynthetic apparatus performance. The R-exposed seedlings contained the highest amount of soluble carbohydrate and together with D-exposed seedlings the lowest amount of chlorophyll in their scions. B-exposed seedlings showed the highest chlorophyll content and improved overall PSII photosynthetic functioning. W-exposed seedling had the largest leaf area, and closely resembled the photosynthetic properties of RB-exposed seedlings. We assume that, during healing of grafted seedlings monochromatic R light should be avoided. Instead, W and monochromatic B light may be willingly adopted due to their promoting effect on shoot, pigments content, and photosynthetic efficiency.     

In-Process Monitoring of Nickel-Based Super Alloy Grinding Using the Acoustic Emission Method

Russian Journal of Nondestructive Testing - One of the most prevalent problems in grinding nickel-based super alloys is grinding wheel loading phenomenon which is the chip accumulation in free...